/* USER CODE BEGIN Header *//**  ******************************************************************************  * @file           : main.c  * @brief          : Main program body  ******************************************************************************  * @attention  *  * 
© Copyright (c) 2021 STMicroelectronics.  * All rights reserved.
  *  * This software component is licensed by ST under BSD 3-Clause license,  * the "License"; You may not use this file except in compliance with the  * License. You may obtain a copy of the License at:  *                        opensource.org/licenses/BSD-3-Clause  *  ******************************************************************************  *//* USER CODE END Header *//* Includes ------------------------------------------------------------------*//**初始化引腳和32基礎設置**/#include "main.h"#include "gpio.h"/* Private includes ----------------------------------------------------------*//* USER CODE BEGIN Includes *//**利用宏定義定義32引腳 高（on）或者低（off）**/#define led0on    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_0, GPIO_PIN_RESET)#define led1on    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_1, GPIO_PIN_RESET)#define led2on    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_2, GPIO_PIN_RESET)#define led3on    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_3, GPIO_PIN_RESET)#define led4on    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_4, GPIO_PIN_RESET)#define led5on    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_5, GPIO_PIN_RESET)#define led6on    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_6, GPIO_PIN_RESET)#define led7on    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_7, GPIO_PIN_RESET)#define led0off    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_0, GPIO_PIN_SET)#define led1off    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_1, GPIO_PIN_SET)#define led2off    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_2, GPIO_PIN_SET)#define led3off    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_3, GPIO_PIN_SET)#define led4off    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_4, GPIO_PIN_SET)#define led5off    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_5, GPIO_PIN_SET)#define led6off    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_6, GPIO_PIN_SET)#define led7off    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_7, GPIO_PIN_SET)#define ledaoff    HAL_GPIO_WritePin(GPIOC,GPIO_PIN_All,GPIO_PIN_SET)//PC全部引腳為高（原理圖是低平點亮 高電平滅）/**利用宏定義設置時間**/#define time    100void gd()	//關閉燈{ledaoff;}	void lsd()	//流水燈{	led0on;	HAL_Delay(time);	//延時時間為time的值	led0off;	HAL_Delay(time);	led1on;	HAL_Delay(time);	led1off;	HAL_Delay(time);	led2on;	HAL_Delay(time);	led2off;	HAL_Delay(time);	led3on;	HAL_Delay(time);	led3off;	HAL_Delay(time);	led4on;	HAL_Delay(time);	led4off;	HAL_Delay(time);	led5on;	HAL_Delay(time);	led5off;	HAL_Delay(time);	led6on;	HAL_Delay(time);	led6off;	HAL_Delay(time);	led7on;	HAL_Delay(time);	led7off;	HAL_Delay(time);}/* USER CODE END Includes *//* Private typedef -----------------------------------------------------------*//* USER CODE BEGIN PTD *//* USER CODE END PTD *//* Private define ------------------------------------------------------------*//* USER CODE BEGIN PD *//* USER CODE END PD *//* Private macro -------------------------------------------------------------*//* USER CODE BEGIN PM *//* USER CODE END PM *//* Private variables ---------------------------------------------------------*//* USER CODE BEGIN PV *//* USER CODE END PV *//* Private function prototypes -----------------------------------------------*/void SystemClock_Config(void);/* USER CODE BEGIN PFP *//* USER CODE END PFP *//* Private user code ---------------------------------------------------------*//* USER CODE BEGIN 0 *//* USER CODE END 0 *//**  * @brief  The application entry point.  * @retval int  */int main(void){  /* USER CODE BEGIN 1 */  /* USER CODE END 1 */  /* MCU Configuration--------------------------------------------------------*/  /* Reset of all peripherals, Initializes the Flash interface and the Systick. */  HAL_Init();  /* USER CODE BEGIN Init */  /* USER CODE END Init */  /* Configure the system clock */  SystemClock_Config();  /* USER CODE BEGIN SysInit */  /* USER CODE END SysInit */  /* Initialize all configured peripherals */  MX_GPIO_Init();    /* USER CODE BEGIN 2 */	gd(); 		//先關閉全部燈  /* USER CODE END 2 */  /* Infinite loop */  /* USER CODE BEGIN WHILE */  while (1)  {	  lsd();		//循環流水燈	  	      /* USER CODE END WHILE */    /* USER CODE BEGIN 3 */  }  /* USER CODE END 3 */}/**  * @brief System Clock Configuration  * @retval None  */void SystemClock_Config(void){  RCC_OscInitTypeDef RCC_OscInitStruct = {0};  RCC_ClkInitTypeDef RCC_ClkInitStruct = {0};  /** Initializes the RCC Oscillators according to the specified parameters  * in the RCC_OscInitTypeDef structure.  */  RCC_OscInitStruct.OscillatorType = RCC_OSCILLATORTYPE_HSE;  RCC_OscInitStruct.HSEState = RCC_HSE_ON;  RCC_OscInitStruct.HSEPredivValue = RCC_HSE_PREDIV_DIV1;  RCC_OscInitStruct.HSIState = RCC_HSI_ON;  RCC_OscInitStruct.PLL.PLLState = RCC_PLL_ON;  RCC_OscInitStruct.PLL.PLLSource = RCC_PLLSOURCE_HSE;  RCC_OscInitStruct.PLL.PLLMUL = RCC_PLL_MUL9;  if (HAL_RCC_OscConfig(&RCC_OscInitStruct) != HAL_OK)  {    Error_Handler();  }  /** Initializes the CPU, AHB and APB buses clocks  */  RCC_ClkInitStruct.ClockType = RCC_CLOCKTYPE_HCLK|RCC_CLOCKTYPE_SYSCLK                              |RCC_CLOCKTYPE_PCLK1|RCC_CLOCKTYPE_PCLK2;  RCC_ClkInitStruct.SYSCLKSource = RCC_SYSCLKSOURCE_PLLCLK;  RCC_ClkInitStruct.AHBCLKDivider = RCC_SYSCLK_DIV1;  RCC_ClkInitStruct.APB1CLKDivider = RCC_HCLK_DIV2;  RCC_ClkInitStruct.APB2CLKDivider = RCC_HCLK_DIV1;  if (HAL_RCC_ClockConfig(&RCC_ClkInitStruct, FLASH_LATENCY_2) != HAL_OK)  {    Error_Handler();  }}/* USER CODE BEGIN 4 *//* USER CODE END 4 *//**  * @brief  This function is executed in case of error occurrence.  * @retval None  */void Error_Handler(void){  /* USER CODE BEGIN Error_Handler_Debug */  /* User can add his own implementation to report the HAL error return state */  __disable_irq();  while (1)  {  }  /* USER CODE END Error_Handler_Debug */}#ifdef  USE_FULL_ASSERT/**  * @brief  Reports the name of the source file and the source line number  *         where the assert_param error has occurred.  * @param  file: pointer to the source file name  * @param  line: assert_param error line source number  * @retval None  */void assert_failed(uint8_t *file, uint32_t line){  /* USER CODE BEGIN 6 */  /* User can add his own implementation to report the file name and line number,     ex: printf("Wrong parameters value: file %s on line %d/r/n", file, line) */  /* USER CODE END 6 */}#endif /* USE_FULL_ASSERT *//************************ (C) COPYRIGHT STMicroelectronics *****END OF FILE****/